2N 2N 2N Units. Collector – Emitter Voltage. VCEO. . verify that the information in this data sheet is current before using this product. Visit for additional data sheets and product information. Forward Current Transfer Ratio. IC = 10 Adc, VCE = 3 Vdc. 2N 2N NPN POWER SILICON TRANSISTOR. Qualified per MIL-PRF/ T4- LDS Rev. 1 (). Page 1 of 5. DEVICES. LEVELS. 2N 2N

Author: Gokazahn Bram
Country: Paraguay
Language: English (Spanish)
Genre: Marketing
Published (Last): 12 October 2012
Pages: 51
PDF File Size: 10.1 Mb
ePub File Size: 11.46 Mb
ISBN: 627-6-31867-739-3
Downloads: 39333
Price: Free* [*Free Regsitration Required]
Uploader: Shakajind

For example, indicates a ? However, to switch ef- ficiently at higher frequencies, several amperes of drive may be required on a pulsed basis in order to quickly charge and discharge the gate capacitances. The values for Rl, R2, and Rsc neglecting base current of Q3 are given by: When connected for Vac operation, the input circuit forms a standard full wave bridge.

2N 데이터시트(PDF) – Central Semiconductor Corp

Resistor R4 is used to guarantee that the power supply will have a minimum output load current of 1. A transistor and rectifier selector guide for switching regulators of various configurations and power levels is provided in Appendix A and B. This method is ‘Needed if supply not current limited Figure Two points on the curve are of interest.

Another very useful reference tool for working with ICs is IC Master, a master selection guide that organizes ICs by type, function and certain key parameters. When more than one color band is used, the widest band represents the first color. Next consider how the replacement interacts with its neighboring components. However, if problems are minimal, catasheet none exist, it is possible to stay with the same core or even consider using the next smaller size.


2N6249 Datasheet

The MC — To fill the need for a low cost, low complexity method of implementing crowbar overvoltage protection which does not suffer the disad- vantages of previous techniques, an IC has been developed for use as an OVP sense and drive circuit, the MC Motorola has provided the selection charts in Appendix A. Determination of Component Values: I turns ratio and is wound by a sandwich technique that improves the coupling between its primary and secondary windings.

All that is left to determine is how the chosen current limit scheme affects required pass element SOA. International Manufacturing Services Inc. Methods for obtaining increased output current are shown in Section 3.

Basic Puise Width Moduiator Controi iC Features required by a control IC vary to some extent because of the particular needs of a designer and on the circuit topology chosen. Screw is at Semi- conductor Case Potential. However, if it is raised to a voltage above 2.

2N6249 Datasheet PDF

Continued from previous page. For the process of choosing an input rectifier, it is useful to visualize the circuit shown in Figure Cable Assembly Silicone 0. This effectively lowers the load regulation of the circuit.


The industry needs something better like powered iron that will datashet permeabilities of 60 to instead of to for this application.

2N Datasheet(PDF) – Savantic, Inc.

This is because regulators are state-of-the-art devices, handling high voltages and currents. In these applications, no gap is used as the high permeability 3 X 0 results in a desirable effect of very low magnetizing current levels.

Order today, get-it tomorrow. Foldback Current Limiting A disadvantage of the constant current limit technique is that in order to obtain sufficient SOA the pass element must have a much greater collector current capability than is actually needed. Typical Operating Characteristic O. Generally it is advisable to have Vceo sus ratings comparable to the tum-on requirements. Q12 will inhibit the output until the ac line is disconnected. This involves checking the turns per inch of wire against the bobbin length.

Housing for female terminals, Mating Pin Diameter: Wakefield, MA 2.

High Input Voltage Occasionally, it may be necessary to power a three terminal regulator from a supply voltage greater than Vin max 35 V or 40 V.