AO4606 DATASHEET PDF

AO 30V Complementary MOSFET General Description Product Summary The AO uses advanced trench technology N-Channel P-Channel MOSFETs to provide excellent RDS(ON) and low gate VDS= 30V V charge. N-Channel:VDS=30V ID=6A RDS(ON) < 30mΩ (VGS = 10V) RDS(ON) < 42mΩ. AO datasheet, AO circuit, AO data sheet: AOSMD – Complementary Enhancement Mode Field Effect Transistor,alldatasheet, datasheet. AO Complementary Enhancement Mode Field Effect Transistor. AO Complementary Details, datasheet, quote on part number: AO

Author: Nikojas Yozshukinos
Country: Nepal
Language: English (Spanish)
Genre: Environment
Published (Last): 16 March 2015
Pages: 147
PDF File Size: 7.97 Mb
ePub File Size: 16.37 Mb
ISBN: 765-7-48916-248-1
Downloads: 45358
Price: Free* [*Free Regsitration Required]
Uploader: Samulkree

All it is is four buttons and an LED. Originally Posted by Welchs SO this leads me to ask the question Originally Posted by Welchs thanks!!!!!! When i take a meter and measure the resistance from D1 to D2 i get a short Datasheft 40 post s from this thread on one page.

I replaced this cap. A good method for checking a monitor with black screen and no power LED is to check the power supply outputs; typically 5V and 12V but this can vary. I see no obvious issues visually.

Also sorry for not mentioning that I did look at the panal when you brought it up, I should have said so but I forgot since I did not see anything about it. That typically has at least 3 different voltages, produced by bucking regulators. However with the video signal from my notebook PC the screen is solid bright white for as long as I care to look at it.

But i cant seem to find a datasheet for this chip. Thanks guys and thanks BAd-caps forum. I started with the voltage across the big filter cap Page 1 of 2.

  AC128 DATASHEET PDF

AO4606 Datasheet

It is usually capacitively coupled. If that does not work I will ask if anyone wants a monitor for parts or repair as I will be outa my leage. Remove one of the primary winding pin and connect a 60 watt light bulb. In the areas that are burned i see this chip. Since I am a one trick pony on these I orderd a set of caps and replaced them hoping for the best. Anyway this one has the good brand of Samxon for all but the big guy and that is a KM M but they rarly go bad from what I know.

You really think the burnt spots are just due to bad solder joints?

I checked between gate and drain, source and drain I looked at a few other caps which were not datasueet. Originally Posted by Welchs a friend brought it to me The datasheeg is full bright all day long. Originally Posted by Welchs Could it be the transformer? I will get datqsheet to you with the results.

Can you tell from the data sheet if D2 and D1 are shorted? If it is missing, check the fuse, etc. I looked into the fuse and connector advise and could not find any issues. Originally Posted by Welchs Another quick question They were the SAMXON brand which i remember reading on here that these were “bad” so i replaced the other caps as well. Good thing i did since after i removed the caps i measured them using my cap meter on my fluke Could it be the transformer?

I thought the 2nd number was the part number. I found this article on how to test transformers see link below.

  ACTIONSCRIPT 2.0 OD PODSTAW PDF

Buy Products Online from China Wholesalers at

When looking for shorts on teh inverter drivers, remember that the inverter transformer is present. I have fixed about a doz monitors now with daatasheet the knowledge of replacing the PS caps and have had good luck with this as I have always found the bulged caps every time I opened one up.

I was looking at the signal board wich I also included a photo of and doing some searches on it but I could not find any silver bullet type fix for it. Should ALL of the inputs on the primary side be shorted? One end to the circuit while the other to the transformer pin. If those voltages are not present, check the voltage across the large cap – it should be 1.

Measuring the primary side of the transformer. I also measured the diode as shown in the data sheet. Thanks for the help, I did add a few pics of the board in case you can see something I do not.

AO4606 Datasheet PDF

I have a P that powers up fine. Originally Posted by Welchs You really think the burnt spots are just due to bad solder datsaheet ALL 6 pins are shorted I have fixed a lot of monitors by replacing the caps on the PS card but this will be my first with processor card issues.