ASTM A513 PDF

Learn about ASTM A steel mechanical tubing and Atlas Tube’s manufacturing capabilities regarding this product for OEM applications. CALIFORNIA. Arrow Route. Rancho Cucamonga, CA WWW. ASTM A TUBING SPECIFICATIONS. TOLERANCES. ASTM A/AM: Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing.

Author: Mijind Zulujind
Country: Montenegro
Language: English (Spanish)
Genre: Relationship
Published (Last): 10 May 2013
Pages: 285
PDF File Size: 14.71 Mb
ePub File Size: 20.6 Mb
ISBN: 237-9-85664-436-1
Downloads: 60964
Price: Free* [*Free Regsitration Required]
Uploader: JoJora

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. The length of the notch shall be compatible with the testing method.

Approved May 1, 1 Revised 5. The twist in square and rectangular tubing may be measured by holding one end of the tubing on a surface plate and noting the height of either corner 5a13 the opposite end of same side above the surface plate. Such requirements shall be considered under the supplementary or basis of purchase provisions of this speci? The purchaser and producer may negotiate special radii. Measurements on tubing with circumferential lay should be longitudinal.

The depth of notch shall not exceed ? Permissible variations in outside diameter for tubing that has been sinkdrawn for closer tolerance on outside diameter are shown in Table 5.

The types of tubing covered here are: Work Item s – proposed revisions of this standard. B Up to 21? Approved September 1, 1 Revised 3.

  KALEED MASNAVI PDF

In this specification hard or rationalized conversions apply to diameters, lengths and tensile properties. It is the intent of this test to reject tubes containing injurious defects. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the a153.

For lengths under 1 ft the straightness tolerance shall be agreed upon between the purchaser and producer.

E Flash Controlled to 0. B,C Outside Diameter, in. Approved December 1, 1 Revised Table 2 to agree with composition requirements contained in Speci? B Up to and incl 11? C These radius tolerances apply to grades of steel covered in Table 1. Cleanup by Centerless Grinding S2. Hydrostatic Test Round Tubing S7. D Round Tubing Outside Diameter, in.

A513 Square Carbon Steel Tube

F Birmingham Wire Gage. Disposition of rejected tubing shall be a matter of agreement between the manufacturer and the purchaser.

ASTM International takes no position respecting the validity of any patent rights asm in connection with any item mentioned in this standard. Disposition of such material shall be a matter for agreement.

Flash-In-Tubing is produced only to outside diameter tolerances and wall thickness tolerances and the inside diameter welding? Last previous edition approved in as A — 06b.

ASTM A513 Mechanical Tubing VS ASTM A519 Mechanical Tubing

Special packaging requiring extra operations other than those normally used by a producer must be speci? Cleanup by Machining S3. Wall Thickness Outside Diameter Range, in.

C Where the ellipsis This specification covers round, square, rectangular, and special atsm electric-resistance-welded carbon and alloy steel mechanical tubing produced by hot- or cold-rolling. Permissible Variations in Dimensions for Round Tubing 8. Committee A01 has identi? These special sections may be made through turkshead rolls or through a die with or without use of a mandrel. This standard has been approved for use by agencies of the Department a5133 Defense.

  ANGEWANDTE TENSORRECHNUNG PDF

Types and Conditions Tubing shall be free of injurious defects and shall have a workmanlike finish. A from the ends of the tubes.

ASTM A Gr Tube, Size: 1/2 Inch, 3/4 Inch, 1 Inch, 2 Inch, 3 Inch | ID:

Soft conversion applies to other Adtm measurements. A — 07 Standard Speci? Any remaining inside diameter? A superscript epsilon e indicates an editorial change since the last revision or reapproval. Permissible variations in wall thickness for tubing made from hot-rolled steel are shown in Table 6. For particular applications, properties may be adjusted by negotiation between purchaser and producer.

Tubing heavier than 16 gage will normally be shipped loose, bundled, or in secured lifts. When specified, tubing shall be coated with a film of rust retarding oil asgm shipping. When an oxide-free surface is speci? A number in parentheses indicates the year of last reapproval.