INTECONT TERSUS MANUAL PDF

Intecont Tersus – Free download as PDF File .pdf), Text File .txt) or read for weighing tasks better than % Manual and/or automatic zero setting Full. The INTECONT Tersus weighing elec- tronics is specially tion module, INTECONT Tersus optimally fits into any Manual and/or automatic zero setting. processes, the INTECONT Tersus meas- uring, control, and supervisory module, INTECONT Tersus optimally fits into any Manual and automatic zero setting.

Author: Nigal Fegar
Country: Eritrea
Language: English (Spanish)
Genre: Medical
Published (Last): 6 February 2008
Pages: 130
PDF File Size: 18.80 Mb
ePub File Size: 17.27 Mb
ISBN: 984-3-17073-940-5
Downloads: 82537
Price: Free* [*Free Regsitration Required]
Uploader: Maujas

Batching mode Batch mode conveys a preset amount of material. Connection diagram for ITE inputs and outputs VWF switch-on sequence Time Condition 1 Feeding does not begin with the on command as the all-clear signal has not been given. Serial interface connection diagram This especially applies to alterations which could affect the operating safety of the system.

Zero setting takes place with an empty belt conveyor with a program which runs automatically.

Belt Skew WM04 Event: Eurotherm Drives Analog Series Manual -? The dimension data should be adapted to the Nominal Flow Rate. The measuring rolls are linked with the frame construction via parallel plate springs.

Intecont Tersus Schenck Calibration Manual pdf However, they will not be cleared. Some operating functions can be triggered by various sources. Belt impact measurement is constant to take changes in regular inteecont into account.

The function can be turned off. It distinguishes alarms red and warnings that either have to be acknowledged orange or do not have to be acknowledged yellow. The internal clock will run for a further approx. No automatic correction is performed.

  ATANDO CABOS ANSWERS PDF

Manual Intecont Tersus

Observe, among other things, the following. In this way an error can be limited between the load cell with wiring inteont electrical equipment.

Belt weigher with a constant load A non-regulated material prefeeder charges a conveyor belt. Set the parameters P Secure them against inadvertent restart. Single-Idler Platform The load on the weighing platform is conducted via a weighing idler into the load cell.

It can be integrated in the control panel or is available with a glass fibre reinforced plastic wall-mounted housing for on-site installation. The hatched area shows the load distribution on the weighing platform. Bvhgb Instruction Manual Intecont Documents. If there is no clearance, memorize the value and report to Schenck Process.

INTECONT® Tersus

Electric W1 P No entry can be made if nanual mode is deselected or if a batch is in process. The Service Values chapter explains the specific data in detail. In this case, L is computed as: Namur Error Belt W1 P Ensure that any connected peripheral devices are functioning correctly before acknowledging an event.

Additionally, you should observe: The full force Q acts on the load cells. If noch tacho is active don’t change characteristic value vs. This means that if the belt load changes, the measurement result for the feed rate will not accord precisely with the current feed rate at the dispatch point.

The product is feed rate I. It covers the en-tire service spectrum, from simple inspections through to tesrus service. Preselection batching mode Preselecting the batching mode makes batching possible, although it does not initiate a batch.

Deselect Batch This function deselects batching mode, i. Attach the calibration weight at the place provided. INTECONT Tersus is a measuring and measurement processing system of continuous weighing and feeding equipment for weighfeeders conveyor belt scales differential feeding scales Coriolis mass flow equipment and solids flow equipment.

  HENRY SCOUGAL PDF

It only shows the functions that can be called up now. However, it is always expe-dient to measure the length manually and to enter the exact value as a parameter. Call up the function Setup – Service Values a tachometer The output frequency of the tachometer generator has to be less than 3, Hz when the measurement is activated.

Intecont Plus Weigh Feeder Documents. Only half of the force from the weight of the terss is passed into the measuring idler. Customized to meet your requirements, our comprehensive Process Advanced Service System provides you with the best service.

Manual Intecont Tersus

It only makes sense with major belt load fluctuations and simple weighing mechanisms. The scales are switched on; feed rate and flow rate are being recorded. This is why the control program will show the same KOR fault quotients after correcting with the value input in P Select the desired function of the second level. The measuring system can be intfcont of a more complex plant.

Belt load measurement is turned off. Password Confirm Defines the access protection for using the operating console.